Post views 1,519 49. Workability of concrete is measured by: Vicat’s apparatus test Slump test Minimum void method Talbot Richard test Answer Slump test 50. Shrinkage in concrete can be reduced by…
Category: Question & Answers
Important Questions about Transportation Engineering -2
Post views 973 1. Peak Hour Flow “PHF” a. Maximum value = 1b. Minimum value = 0.25c. Maximum value = 1.5d. Minimum value = 0.5 Correct Selection: 1. “a” and “b”2. “c” and…
Important Questions about Fluid Mechanics & Hydraulics -2
Post views 936 27. The continuity equation in fluid mechanics is derived based on:a. Conservation of massb. Conservation of energyc. Conservation of momentumd. Conservation of velocity Answer Conservation of mass 28. The…
Important Questions about Project Management -2
Post views 841 What is the least level of WBS ? 1. Deliverable2. Cost3. Work package4. Lowest sub deliverable Answer Work package 2. What is meant by ethics ? Codes of behavior…
Important Questions about Foundation & Soil Mechanics -2
Post views 1,173 25. Required compaction for soil? 98 →99 % 100 →101 % 94→ 96 % 92 →94 % Answer 98 →99 % 26. During percussion drilling: Ground water observation are…
Important Questions about Structural Analysis -2
Post views 1,099 28. A simply supported beam of span “L” carries a uniformly distributed load “W”, the maximum bending moment “M” is: WL4 / 2 WL3 / 4 WL2 / 8…
Important Questions for Engineering Materials -2
Post views 1,000 23. Which of the following materials has the highest compressive strength a) Woodb) Steelc) Concreted) Brick Answer Concrete 24. Gypsum board is used due to a) Low cost.b) Ease…
Important Questions about Surveying – 2
Post views 999 27. What is surveying? A) The art of measuring land and mapping the physical features.B) The study of geology.C) The process of land grading.D) The measurement of time. Answer…
Important Questions About Concrete -2
Post views 1,290 25. Why steel is preferred as reinforcement in concrete? Because it is inexpensive and resistant Because it is easily accessible Because it adheres well to concrete Because it has…
Important Questions about Sanitary Engineering -1
Post views 2,902 1. The PH value of fresh sewage is usually a. Equal 5 b. 5 to 7 c. More than 7 d. Less than 7 Answer More than 7 2. The rate of accumulation…
Important Questions about Transportation Engineering -1
Post views 3,780 1. While designing intersection, consider a. Speed/travel time b. Density c. Delay d. All of above Answer All of above 2. Curves At-Grade intersection should consider a. Angle of turn b. Turning speed …
Important Questions about Fluid Mechanics & Hydraulics -1
Post views 1,870 1. Water Concentration a. 61.6 (mol/l) b. 59.7 (mol/l) c. 58.8 (mol/l) d. 55.6 (mol/l) Answer 55.6 (mol/l) 2. Water Molar Mass a. 38 (g/mol) b. 18 (g/mol) c. 28 (g/mol) d. 48 (g/mol) Answer 18 (g/mol)…
Important Questions about Project Management -1
Post views 2,044 1. First step of Scope planning starts with ? a) Budgeting b) Current earning estimation c) Objectives and requirements to satisfy customer d) None of the above Answer Objectives and requirements to satisfy…
Important Questions about Foundation & Soil Mechanics -1
Post views 2,219 1. Compaction equipment can be used for sand or clay material as following a) Roller for sand & clay b) Foot-shape for sand & clay c) Foot-shape for sand d) Roller for sand Answer Roller for…
Important Questions about Structural Analysis -1
Post views 2,590 1. 2-way slab sides lifting caused by? a) High punching shear b) Torsion c) Unbalanced moment d) Resulting moment e) Resulting shear Answer Torsion 2. What is the maximum live load had to…
Important Questions for Engineering Materials -1
Post views 3,718 1. The strength of material is defined as ? a. Ability of material to resist external forces b. Ability of material to resist deformation c. Ability of material to withstand external loads d….
Important Questions about Surveying – 1
Post views 3,574 1. Line connecting the same elevation on the drawing known as ? a. Super elevation b. Grade line c. Contour line d. None of these Answer Contour line 2….
Important Questions About Concrete – 1
Post views 5,221 1. Process of keeping Concrete moist for certain period after casting is ? a. Finishing of Concrete b. Curing of Concrete c. Placing of Concrete d. None of the above Answer Curing of Concrete 2….